• Wide input up to 100V — 24V / 48V / 60V / 80V input classes cover 12V, 24V, 36V, 48V and 72V battery systems
• Up to 96% peak efficiency with synchronous rectification — runs cool with natural convection, no fan
• 3 compact housings, 30W to 100W — C2A (57.5×24.5×4.2 mm), C2B (57.5×24.5×4.2 mm), C3 (75.5×24.5×4.5 mm)
• IP67, fully potted ABS case — dust-tight, waterproof and shock-resistant for vehicles and outdoor gear
• Full protection — input under-voltage, output over-current, short-circuit and over-temperature; reverse-input protection on 48V+ internal-MOSFET models
• Ultra-low 2 mA no-load current (internal-MOSFET models) — ideal for always-on battery loads
SKU:
The aluminum profile shell C series power buck converter can convert high voltage into stable low voltage; The aluminum shell has strong thermal conductivity, allowing it to quickly dissipate working heat and prevent internal components from malfunctioning due to high temperatures, remaining stable even after long-term use. The shell is highly hard and resistant to everyday impacts, paired with a sealed design that is dustproof and moisture-proof, providing reliable voltage reduction support for motors, electronic instruments, and small household appliances, balancing durability and practicality to meet diverse power supply needs.
A DC-DC buck converter is a type of switching power supply module that converts an input DC voltage into a lower, stable DC voltage—for example, stepping down 48V to 12V, or 24V to 5V. Unlike linear voltage regulators, it operates by switching the input signal at a high frequency; consequently, energy loss (in the form of heat) is extremely low. Modern synchronous buck converters typically achieve an efficiency of approximately 92% to 96%.
Product features
* Input peak voltage 100V, output peak power 120W;
* High conversion efficiency, up to 97%;
* Built-in MOSFET output Peak Current 5A, no-load current less than 2mA;
* External MOSFET outputs peak current of 15A;
* Some products have input reverse connection protection (built-in MOSFET series, input 48V or above);
* High efficiency, low power consumption (C2B series);
* Aluminum profile housing, compact size, good heat dissipation;
* Full potting adhesive, natural cooling, IP67 protection;
* Equipped with protection against input undervoltage, output overcurrent, output short circuit, and overtemperature
Specifications
| Model | Product series | Input voltage | No-load current | Conversion efficiency | Output voltage | Output current | Maximum power | Drive method |
| EP-C2A | 24V voltage reduction | 8~36V | 2mA | 95% | 3~20V | 3A | 36W | Built-in MOS |
| EP-C2A | 8~36V | 2mA | 95% | 3~20V | 3A | 36W | Built-in MOS | |
| EP-C2A | 24V voltage reduction | 8~36V | 0.2mA | 95% | 3~20V | 5A | 50W | Built-in MOS |
| EP-C2B | 48V buck | 8~60V | 1.5mA | 93% | 3~36V | 5A | 50W | Built-in MOS |
| EP-C2B | 60V buck | 8~75V | 1.5mA | 93% | 3~36V | 3A | 50W | Built-in MOS |
| EP-C2B | 80V buck | 8~100V | 1.5mA | 93% | 3~30V | 2A | 50W | Built-in MOS |
| EP-C3 | 24V voltage reduction | 9~40V | 2mA | 95% | 3~20V | 10A | 120W | External MOS |
| EP-C3 | 48V buck | 8~60V | 12mA | 94% | 3~56V | 10A | 120W | External MOS |
| EP-C3 | 60V buck | 8~80V | 12mA | 94% | 3~60V | 10A | 120W | External MOS |
| EP-C3 | 80V buck | 8~100V | 12mA | 94% | 3~60V | 10A | 120W | External MOS |
How to Connect the C-Series Step-Down Converter
Check the label—verify that the input voltage range covers the full-charge voltage of your battery, and ensure the output voltage matches your load requirements.
Disconnect the power source before wiring.
Input connections: Connect the red wire to the positive (+) battery terminal and the black input wire to the negative (−) battery terminal. Install a fuse on the battery line, close to the battery.
Output connections: Connect the yellow wire to the positive (+) terminal of the load, and the black output wire to the negative (−) terminal of the load. The input and output share a common ground.
Use heat-shrink tubing to insulate each terminal to maintain an IP67 ingress protection rating at the connection points.
Secure the module to a grounded surface with adequate airflow using the mounting tabs; ensure the cooling fins remain unobstructed to allow for proper heat dissipation.
Before connecting sensitive equipment, use a multimeter to verify the output voltage.
Applications
Vehicles and Fleets—Powering 12V radios, cameras, GPS units, and USB chargers in 24V trucks and buses.
Golf Carts, E-bikes, and E-scooters—Powering 12V lights, horns, and displays from 36V/48V/72V battery packs.
Forklifts, AGVs, and Industrial Vehicles—Providing stable 12V or 24V power for controllers and sensors.
Marine and RVs—Waterproof power solutions for water pumps, LED lighting, and electronic devices.
Solar and Off-Grid Systems—Powering 5V/12V loads from battery banks with near-zero idle power consumption.
Smart Home and IoT—Supplying low-voltage power to sensors, microcontrollers, and access control systems.
Telecommunications and Security—Converting 48V DC to 12V for networking and security equipment.
Why Choose EpevsPower
Direct from Manufacturer—Standard models and custom output voltage options available from a single source.
100% automated testing and burn-in testing performed before shipment.
Customization Options—Available for output voltage, cable length, connectors, and private-label branding.
Samples and datasheets provided upon request; inquiries answered within 24 hours.
Minimum Order Quantity / Lead Time: 10 units, 5 days
| Housing | C2A (36W), C2B (50W), C3 (100W) |
|---|---|
| Input Voltage | 8-36V, 9-40V, 8-60V, 8-80V, 8-100V |
| Output Voltage | 3-20V, 3-36V, 3-56V, 3-60V |




Tell us what you need — our engineers reply within 24 hours.