Epevspower Step-Down Power Module DC-DC 12V/24V to 5V 5A Universal Buck Converter Module for Intelligent Robots

• Wide input up to 100V — 24V / 48V / 60V / 80V input classes cover 12V, 24V, 36V, 48V and 72V battery systems
• Up to 96% peak efficiency with synchronous rectification — runs cool with natural convection, no fan
• 2 compact housings, 30W to 100W — F150,F220
• IP67, fully potted ABS case — dust-tight, waterproof and shock-resistant for vehicles and outdoor gear
• Full protection — input under-voltage, output over-current, short-circuit and over-temperature; reverse-input protection on 48V+ internal-MOSFET models
•  Input peak voltage 100V

Product Introduction

The EpevsPower F Series high-power buck converter with aluminum profile housing, a non-isolated DC high-power buck power module equipped with high-end components, is specially designed for high-power scenarios. The aluminum profile housing design is sturdy and durable, impact-resistant, and corrosion-resistant, allowing for rapid and stable dissipation of large current heat, preventing overheating, efficiency degradation, or damage, ensuring continuous and stable operation. Suitable for high-power power supply needs such as motor drives and heavy industrial equipment, balancing reliability and environmental adaptability.

What Is a DC-DC Buck Converter?

A DC-DC buck converter is a switching power module that converts a higher DC voltage into a lower, regulated DC voltage — for example 48 V to 12 V or 24 V to 5 V. Unlike a linear regulator, it switches the input on and off at high frequency and filters the result, so it wastes very little energy as heat. Modern synchronous buck converters reach 92–96% efficiency.

F Series Key Features

*Input peak voltage 100V;

* Peak output power of 1400W;

* High conversion efficiency, up to 97%;

* Stable output typical current of 120A;

* High peak current, connected to inductive loads;

* Full potting adhesive, natural cooling, IP67 protection;

* Aluminum profile casing for stable dissipation of large current heat;

* Protection against undervoltage, overcurrent, short circuit, overtemperature, etc.;

* Input and output ground wires connected to common terminals, reducing wiring complexity

Specifications

 

Model Product series Input voltage No-load current Conversion efficiency Output voltage Output current Maximum power Drive method
EP-F150 24V voltage reduction 8~40V 35mA 95% 3~20V 90A 1000W External MOS
EP-F150 48V buck 8~60V 35mA 95% 3~56V 80A 1000W External MOS
EP-F150 60V buck 8~80V 35mA 95% 3~60V 80A 1000W External MOS
EP-F150 80V buck 8~100V 35mA 95% 3~60V 80A 1000W External MOS
EP-F220 24V voltage reduction 8~40V 54mA 95% 3~20V 120A 1400W External MOS
EP-F220 48V buck 8~60V 54mA 95% 3~56V 100A 1400W External MOS
EP-F220 60V buck 8~80V 54mA 95% 3~60V 100A 1400W External MOS
EP-F220 80V buck 8~100V 54mA 95% 3~60V 100A 1400W External MOS

 How to Wire the F Series Buck Converter

  1. Check the label — confirm the input range covers your battery’s full-charge voltage and the output matches your load.
  2. Disconnect power before wiring.
  3. Connect input: Red wire to battery positive (+), the input-side Black wire to battery negative (−). Add a fuse on the positive line close to the battery.
  4. Connect output: Yellow wire to load positive (+), the output-side Black wire to load negative (−). Input and output share a common ground.
  5. Insulate every joint with heat-shrink tubing to keep the IP67 rating at the connection.
  6. Mount the module with two screws through the ears on a flat surface with some airflow; keep the leads pointing downward so water cannot run along them.
  7. Power up and measure the output with a multimeter before connecting sensitive devices.

Applications

  • Vehicles & fleets — 24 V trucks and buses powering 12 V radios, cameras, GPS, USB chargers.
  • Golf carts, e-bikes and e-scooters — 36 V / 48 V / 72 V packs to 12 V lights, horns and displays.
  • Forklifts, AGVs and industrial vehicles — stable 12 V or 24 V for controllers and sensors.
  • Marine & RV — waterproof power for pumps, LED lights and electronics.
  • Solar & off-grid systems — battery bank to 5 V / 12 V loads with near-zero standby drain.
  • Smart home & IoT — low-voltage supply for sensors, microcontrollers and access-control devices.
  • Telecom & security — 48 V DC to 12 V for cameras and network gear.

Why Choose EpevsPower

  • Factory-direct — standard J Series and custom output voltages from one source.
  • 100% automated testing and burn-in before shipment.
  • Custom options — output voltage, wire length, connectors and private-label printing
  • Samples and datasheets on request, reply within 24 hours.
  • MOQ / lead time: 10PC, 5 Days

 

Additional information

Weight 1 kg
Dimensions 15 × 15 × 70 cm
Housing

F150(800W), F220(1500W)

Input Voltage

8-36V, 9-40V, 8-60V, 8-80V, 8-100V

Output Voltage

3-20V, 3-56V, 3-60V

0
Quote List 0 items

Your quote list is empty.

Request a Quote

Tell us what you need — our engineers reply within 24 hours.