Dc to Dc Step up Converter 5V 12V to 24V 36V 48V 60V 72V 1A 2A 3A Boost Power Supply Module

  • Input voltage range: 8~100V
  • Waterproof rating: IP67
  • Output voltage range values: 3~60V
  • Cooling method: The natural breeze is cool
  • Output current range values: 0~10A
  • Operating temperature: -40℃~65℃
  • Up to 95% efficiency — three-sided heat-sink fins cool the module without a fan
  • IP67, fully potted — waterproof, dustproof and shock-resistant for vehicles and industrial equipment
  • Bypass when input exceeds output and anti-backflow protection (asynchronous models)
  • Soft start + full protection — input under-voltage, over-current, short-circuit and over-temperature

Overview

The epevspower J Series plastic-shelled buck converter is an electronic module that converts high voltage into stable low voltage. The plastic casing combines protection (impact and dust resistance) with insulation functions, enhancing safety. Its compact size and convenient installation make it suitable for smart homes and small electronic devices, providing stable power for low-voltage devices such as sensors and microcontrollers to ensure safe operation

Enclosure packaging Product series Input voltage No-load current Conversion efficiency Output voltage Output current Maximum power Drive method
EP-J2 5V boost 5~11V 17mA 95% 6~15V 2A 50W Asynchronous
J2 housing 12V boost voltage 8~30V 9mA 16~56V 2A 50W
EP-J3 5V boost 5~11V 17mA 93% 6~15V 3A 120W Asynchronous
J3 housing 12V boost voltage 8~20V 17mA 16~56V 3A 120W
EP-J3 24V boost 18~60V 17mA 31~80V 2A 120W

What Is a DC-DC Boost Converter?

A DC-DC boost converter is a switching power module that raises a lower DC voltage to a higher, regulated DC voltage — for example 12 V to 24 V or 24 V to 48 V. It stores energy in an inductor and releases it at a higher voltage, so it can run 24 V or 48 V equipment from a 12 V or 24 V battery. Modern boost converters reach 92–95% efficiency.

J Series Key Features

* Input peak voltage 100V, output peak power 120W;
* High conversion efficiency, peak up to 96%;
* Built-in MOSFET output peak current of 5A, no-load current less than 2mA;
* External MOSFET output peak current is 15A;
* Some products feature reverse polarity protection (built-in MOSFET series, input 48V or above);
* Equipped with input undervoltage protection, output overcurrent protection, output short-circuit protection, and over-temperature protection functions;
* ABS material, full potting adhesive, natural heat dissipation, IP67 protection rating;
* Utilizes brand-new high-efficiency synchronous rectification and voltage reduction technology;
* Strong load capacity, output power can be adaptive;
* External MOSFET products feature over-temperature delayed startup protection

How to Wire the J Series Boost Converter

  1. Check the voltages — your highest input voltage must stay below the output voltage.
  2. Disconnect power before wiring.
  3. Connect input: Red to battery positive (+), the input-side Black to battery negative (−). Use wire and a fuse rated for the input current — at 500 W from 12 V, input current exceeds 40 A.
  4. Connect output: Yellow to load positive (+), the output-side Black to load negative (−). Input and output share a common ground.
  5. Insulate every joint with heat-shrink tubing.
  6. Mount the module with screws on a flat metal surface where air can flow over the fins.
  7. Power up and measure the output before connecting the load.

 Applications

  • Onboard vehicle power — run 24 V equipment in 12 V cars, vans and RVs.
  • Trucks & buses — 24 V to 48 V for telematics, cameras and tail-lifts.
  • Car audio & laptops — 12 V to 19 V / 24 V / 36 V.
  • Industrial equipment — stable high-voltage rails for motors, pumps and controllers.
  • Solar & off-grid — 12 V or 24 V battery banks to 48 V loads.
  • Telecom & PoE — 12 V or 24 V to 48 V for network and radio equipment.

Why Choose EpevsPower

  • Factory-direct — standard Y Series and custom output voltages from one source.
  • 100% automated testing and burn-in before shipment.
  • Custom options — output voltage, wire length, connectors and private label 【TBC】.
  • Samples and datasheets on request, reply within 24 hours.
  • MOQ / lead time:

Additional information

Housing

J1(30W), J2(72W), J3(120W)

Input Voltage

5-14V, 9-24V, 9-35V, 9-55V, 18-60V

Output Voltage

6-15V, 15-30V, 32-56V, 58V-UP

0
Quote List 0 items

Your quote list is empty.

Request a Quote

Tell us what you need — our engineers reply within 24 hours.