Epevspower DC-DC Converter 48V to 5V12V 24V 5A Volt Reducer for Dash Cam

• Wide input up to 100V — 24V / 48V / 60V / 80V input classes cover 12V, 24V, 36V, 48V and 72V battery systems
• Up to 96% peak efficiency with synchronous rectification — runs cool with natural convection, no fan
• 3 compact housings, 30W to 100W — D25,D50,D50H
• IP67, fully potted ABS case — dust-tight, waterproof and shock-resistant for vehicles and outdoor gear
• Full protection — input under-voltage, output over-current, short-circuit and over-temperature; reverse-input protection on 48V+ internal-MOSFET models
• Ultra-low 2 mA no-load current (internal-MOSFET models) — ideal for always-on battery loads

Overview

The EpevsPower aluminum profile housing D Series Buck Converter not only retains the core advantages of efficient buck power supply bucking and stable output, but also relies on the characteristics of aluminum profiles to enhance practicality and reliability. The aluminum profile housing has excellent thermal conductivity, allowing it to quickly dissipate heat from components such as switching tubes and inductors, ensuring stable operation under heavy loads or for extended periods; The structure is sturdy and well sealed, making it impact-resistant, dustproof, and moisture-proof, suitable for complex environments such as industrial and automotive applications.

What Is a DC-DC Buck Converter?

A DC-DC buck converter is a switching power module that converts a higher DC voltage into a lower, regulated DC voltage — for example 48 V to 12 V or 24 V to 5 V. Unlike a linear regulator, it switches the input on and off at high frequency and filters the result, so it wastes very little energy as heat. Modern synchronous buck converters reach 92–96% efficiency.

D Series Key Features

* Input peak voltage 100V, output peak power 120W;
* High conversion efficiency, up to 96%;
* Built-in MOSFET outputs peak current of 5A, no-load current less than 2mA;
* External MOSFET outputs peak current of 15A;
* Some products have input reverse connection protection (built-in MOSFET series, input 48V or above);
* Full potting adhesive, natural cooling, IP67 protection;
* Aluminum profile housing, compact size, good heat dissipation;
* Equipped with protection against input undervoltage, output overcurrent, output short circuit, and overtemperature;
* Can operate at 100% full power for long periods (mounted on a metal casing)

Model Product series Input voltage No-load current Conversion efficiency Output voltage Output current Maximum power Drive method
EP-D25 24V voltage reduction 8~36V 2.7mA 95% 3~20V 5A 50W Built-in MOS
EP-D25 48V buck 8~60V 2mA 93% 3~36V 5A 50W Built-in MOS
EP-D25 60V buck 8~75V 2mA 93% 3~36V 3A 36W Built-in MOS
EP-D25 80V buck 8~100V 2mA 93% 3~30V 2A 36W Built-in MOS
EP-D50/D50H 24V voltage reduction 9~40V 2.7mA 95% 3~20V 10A 120W External MOS
EP-D50/D50H 48V buck 8~60V 3.6mA 94% 3~56V 10A 120W External MOS
EP-D50/D50H 60V buck 8~80V 21mA 94% 3~60V 10A 120W External MOS
EP-D50/D50H 80V buck 8~100V 23mA 94% 3~60V 10A 120W External MOS

 

 How to Wire the D Series Buck Converter

  1. Check the label — confirm the input range covers your battery’s full-charge voltage and the output matches your load.
  2. Disconnect power before wiring.
  3. Connect input: Red wire to battery positive (+), the input-side Black wire to battery negative (−). Add a fuse on the positive line close to the battery.
  4. Connect output: Yellow wire to load positive (+), the output-side Black wire to load negative (−). Input and output share a common ground.
  5. Insulate every joint with heat-shrink tubing to keep the IP67 rating at the connection.
  6. Mount the module with two screws through the ears on a flat surface with some airflow; keep the leads pointing downward so water cannot run along them.
  7. Power up and measure the output with a multimeter before connecting sensitive devices.

Applications

  • Vehicles & fleets — 24 V trucks and buses powering 12 V radios, cameras, GPS, USB chargers.
  • Golf carts, e-bikes and e-scooters — 36 V / 48 V / 72 V packs to 12 V lights, horns and displays.
  • Forklifts, AGVs and industrial vehicles — stable 12 V or 24 V for controllers and sensors.
  • Marine & RV — waterproof power for pumps, LED lights and electronics.
  • Solar & off-grid systems — battery bank to 5 V / 12 V loads with near-zero standby drain.
  • Smart home & IoT — low-voltage supply for sensors, microcontrollers and access-control devices.
  • Telecom & security — 48 V DC to 12 V for cameras and network gear.

Why Choose EpevsPower

  • Factory-direct — standard J Series and custom output voltages from one source.
  • 100% automated testing and burn-in before shipment.
  • Custom options — output voltage, wire length, connectors and private-label printing
  • Samples and datasheets on request, reply within 24 hours.
  • MOQ / lead time: 10PC, 5 Days

 

Additional information

Housing

D25 (30W), D50 (50W), D50H (100W)

Input Voltage

8-36V, 9-40V, 8-60V, 8-80V, 8-100V

Output Voltage

5V, 12V, 24V

0
Quote List 0 items

Your quote list is empty.

Request a Quote

Tell us what you need — our engineers reply within 24 hours.